Expansion Connector
The phyCORE-AM62x development kit provides a 60-pin 2mm expansion connector that brings out signals that were either not used elsewhere on the carrier board or were considered useful to have easy access too. For signals not used by either the SOM or the carrier board, they can be freely multiplexed to enable different functionality at the expansion connector. To learn more information about the phyCORE-AM62x multiplexing, please refer to the Hardware Manual.

Pin Number |
Signal |
Description (lists default muxing) |
---|---|---|
1 |
USB-C_PP_HV1 |
USB-C PP HV1 power rail |
2 |
VCC_5V0_SW |
5.0V Carrier Board power rail |
3 |
VCC_3V3_SW |
3.3V Carrier Board power rail |
4 |
VCC_5V0_MAIN |
Main 5.0V SOM power rail |
5 |
VCC_1V8_EXP_CON |
1.8V Carrier Board power rail |
6 |
GND |
Ground |
7 |
GND |
Ground |
8 |
X_JTAG_EMU0 |
Emulation Control 0. Connected to JTAG circuit on Carrier Board. |
9 |
X_WKUP_CLKOUT0 |
WKUP Domain CLKOUT0 output. Only connected to pin D60 of the SOM connector. |
10 |
X_JTAG_EMU1 |
Emulation Control 1. Connected to JTAG circuit on Carrier Board. |
11 |
X_MCU_UART0_RTSN |
MCU UART0 Request to Send (active low). Only connected to pin D54 of the SOM connector. |
12 |
X_MCASP0_AXR3/UART1_CTSn |
UART1 Clear to Send (active low). Only connected to pin C28 of the SOM connector. |
13 |
X_MCU_UART0_CTSN |
MCU UART0 Clear to Send (active low). Only connected to pin D53 of the SOM connector. |
14 |
X_MCASP0_ACLKR/UART1_TXD |
UART1 Transmit Data. Only connected to pin C30 of the SOM connector. |
15 |
X_WKUP_UART0_RXD |
WKUP UART0 Receive Data. Only connected to pin B58 of the SOM connector. |
16 |
X_MCASP0_AXR2/UART1_RTSn |
UART1 Request to Send (active low). Only connected to pin C27 of the SOM connector. |
17 |
X_WKUP_UART0_TXD |
WKUP UART0 Transmit Data. Only connected to pin B57 of the SOM connector. |
18 |
X_GPMC0_BE1n/GPIO0_36 |
GPIO. Only connected to pin C18 of the SOM connector. |
19 |
GND |
Ground |
20 |
X_MCASP0_AFSR/UART1_RXD |
UART1 Receive Data. Only connected to pin D32 of the SOM connector. |
21 |
X_MCU_SPI0_CLK |
MCU SPI0 Clock. Connected to SPI EEPROM. |
22 |
NC |
No connect |
23 |
X_MCU_SPI0_D0 |
MCU SPI0 Data 0. Connected to SPI EEPROM. |
24 |
NC |
No connect |
25 |
X_MCU_SPI0_D1 |
MCU SPI0 Data 1. Connected to SPI EEPROM. |
26 |
GND |
Ground |
27 |
X_MCU_SPI0_CS1 |
MCU SPI0 Chip Select 1. Connected to SPI EEPROM. |
28 |
LEFT_LOP |
Left line output. Coonected to audio codec. |
29 |
GND |
Ground |
30 |
RIGHT_LOP |
Right line output. Connected to audio codec. |
31 |
X_MCU_MCAN0_TX |
MCU MCAN0 Transmit Data. Only connected to pin A57 of the SOM connector. |
32 |
NC |
Not connected |
33 |
X_MCU_MCAN0_RX |
MCU MCAN0 Receive Data. Only connected to pin A58 of the SOM connector. |
34 |
X_SPI0_CS0 |
SPI0 Chip Select 0. Only connected to pin C40 of the SOM connector. |
35 |
X_MCU_MCAN1_RX |
MCU MCAN0 Receive Data. Only connected to pin A60 of the SOM connector. |
36 |
X_SPI0_CS1/EHRPWM0_B/LVDS_PWM |
EHRPWM Output B. Connected to LVDS circuit. |
37 |
X_MCU_MCAN1_TX |
MCU MCAN0 Transmit Data. Only connected to pin A59 of the SOM connector. |
38 |
X_SPI0_CLK |
SPI0 CLock. Only connected to pin D40 of the SOM connector. |
39 |
GND |
Ground |
40 |
X_SPI0_D0 |
SPI0 Data 0. Only connected to pin D41 of the SOM connector. |
41 |
X_I2C0_SCL |
I2C0 Clock. Used on the SOM. |
42 |
X_SPI0_D1 |
SPI0 Data 1. Only connected to pin D42 of the SOM connector. |
43 |
X_I2C0_SDA |
I2C0 Data. Used on the SOM. |
44 |
GND |
Ground |
45 |
X_WKUP_I2C0_SCL |
WKUP I2C0 Clock (Requires pullup). Only connected to pin D50 of the SOM connector. |
46 |
X_CPSW_ETH1_GPIO_0 |
ETH1 GPIO 0. Connected to ETH1 PHY. |
47 |
X_WKUP_I2C0_SDA |
WKUP I2C0 Data (Requires pullup). Only connected to pin D51 of the SOM connector. |
48 |
X_CPSW_ETH1_GPIO_1 |
ETH1 GPIO 1. Connected to ETH1 PHY. |
49 |
GND |
Ground |
50 |
GND |
Ground |
51 |
X_MCU_SAFETY_ERRORn |
Error Signal Output. Only connected to pin D59 of the SOM connector. |
52 |
X_RTC_INT |
RTC Interrupt. Connected to RTC. |
53 |
X_RESETSTATz |
Main Domain warm reset status output. Connected to RESET circuit. |
54 |
X_WKUP_UART0_RTSN |
WKUP UART0 Request to Send (active low). Only connected to pin B59 of the SOM connector. |
55 |
X_MCU_RESETSTATz |
MCU Domain warm reset status output. Only connected to pin C55 of the SOM connector. |
56 |
X_WKUP_UART0_CTSN |
WKUP UART0 Clear to Send (active low). Only connected to pin A56 of the SOM connector. |
57 |
NC |
Not connected |
58 |
X_USB0_DRVVBUS |
USB VBUS control output (active high). Only connected to pin A41 of the SOM connector. |
59 |
GND |
Ground |
60 |
GND |
Ground |