EEPROM

This guide will show you how to access the 2Kbit EEPROM featured on the phyCORE-AM62Ax development kit carrier board. To learn more information about the phyCORE-AM62Ax EEPROM system memory, please see section 6.1.2 in the Hardware Manual.

Note

The phyCORE-AM62Ax development kit provides access to two EEPROMs, 1x 32Kbit EEPROM on the SOM and a 2Kbit EEPROM on the carrier board.

Boot Settings

Location	Reference	I2C Bus	Address
SOM	U20	i2c0	0x50
Carrier Board	U38	i2c1	1x51

Verifying EEPROM Initialization

• First ensure that the EEPROM is initialized correctly by checking the boot log.

  Target (Linux)

  dmesg | grep -i "eeprom"
  

  Expected Output

  root@phyboard-lyra-am62axx-2:~# dmesg | grep -i "eeprom"
  [    6.049192] at24 0-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write
  [    6.090717] at24 1-0051: 256 byte 24c02 EEPROM, writable, 16 bytes/write
  

Writing to the EEPROM

• Clear out the entirety of the EEPROM by writing zeros to it.

  Target (Linux)

  dd if=/dev/zero of=/sys/bus/i2c/devices/1-0051/eeprom bs=256 count=1
  

  Expected Output

   root@phyboard-lyra-am62axx-2:~# dd if=/dev/zero of=/sys/bus/i2c/devices/1-0051/eeprom bs=256 count=1
   1+0 records in
   1+0 records out
   256 bytes copied, 0.0903406 s, 2.8 kB/s
  

• Now generate a 2Kbit file with random data. This will serve as the test file:

  Target (Linux)

   dd if=/dev/urandom of=/tmp/test.img bs=256 count=1
  

  Expected Output

   root@phyboard-lyra-am62axx-2:~# dd if=/dev/urandom of=/tmp/test.img bs=256 count=1
   1+0 records in
   1+0 records out
   256 bytes copied, 0.000203318 s, 1.3 MB/s
  

• Write the test file to the EEPROM

  Target (Linux)

  dd if=/tmp/test.img of=/sys/bus/i2c/devices/1-0051/eeprom bs=512 count=1
  

  Expected Output

  root@phyboard-lyra-am62axx-2:~# dd if=/tmp/test.img of=/sys/bus/i2c/devices/1-0051/eeprom bs=256 count=1
  0+1 records in
  0+1 records out
  256 bytes copied, 0.076665 s, 3.3 kB/s
  

Reading from EEPROM

• Read the contents of the EEPROM and store it to a file.

  Target (Linux)

  dd if=/sys/bus/i2c/devices/1-0051/eeprom of=/tmp/test_read.img  bs=256 count=1
  

  Expected Output

   root@phyboard-lyra-am62axx-2:~# dd if=/sys/bus/i2c/devices/1-0051/eeprom of=/tmp/test_read.img  bs=256 count=1
   1+0 records in
   1+0 records out
   256 bytes copied, 0.00792198 s, 32.3 kB/s
  

• Make sure the output file was not corrupted during the transfer using md5sum.

  Target (Linux)

   md5sum /tmp/test.img /tmp/test_read.img
  

  Expected Output

   root@phyboard-lyra-am62axx-2:~# md5sum /tmp/test.img /tmp/test_read.img
   192e08b78bc0100bcff74d324d1ccbde  /tmp/test.img
   192e08b78bc0100bcff74d324d1ccbde  /tmp/test_read.img
  

Reading/Writing to the SOM EEPROM

The SOM EEPROM is used for PHYTEC’s Hardware Introspection, which allows to automatically load the correct software for the underlaying SOM configuration.

Do not modify the content, except the BSP doesn’t use the Hardware Introspection.