BSP-Yocto-NXP-i.MX7-PD23.1.0
This document highlights the key features and support included in the BSP-Yocto-NXP-i.MX7-PD23.1.0 software release for the phyCORE-i.MX7 SOM and development kit.
BSP Operating system |
Linux |
|---|---|
Release Status |
RELEASED |
Release Date |
2023-12-15 |
Repository |
|
Binaries |
New in this Release
Yocto
Switched to PHYTEC Ampliphy Distro
Known Issues
If the processor is stressed with stressapptest or other heavy system loads the system may crash after some period of time under normal operation conditions.
Software Versioning
The BSP-Yocto-NXP-i.MX7-PD23.1.2 software release is largely based off of NXP’s 2.2.2 Processor SDK Linux release and shares much of the same components and features.
Tested Build Environment |
Ubuntu 20.04 |
|
|---|---|---|
Linux Kernel |
v5.15.71 (tag: v5.15.71_2.2.2-phy3) |
|
U-Boot Bootloader |
v2022.04 (tag: v2022.04_2.2.2-phy5) |
|
Yocto |
4.0.14 Kirkstone (tag: BSP-Yocto-NXP-i.MX7-PD23.1.0) |
PHYTEC Meta Layer
This BSP release supports various configurations of the phyCORE-i.MX7 SOM and Development Kit, here is a summary of the Yocto MACHINE configuration support included in the PHYTEC Meta Layer for this release:
Yocto MACHINE |
Default Target Image |
Linux Distro |
Kit Part Number |
Compatible Modules |
U-Boot defconfig |
Linux defconfig |
Device Tree Files |
|---|---|---|---|---|---|---|---|
phyboard-zeta-imx7d-1 (Default Kit) |
phytec-qt6demo-image |
PHYTEC Ampliphy Reference Distribution |
KPB-01910-004.A0 |
PHYTEC phyCORE-i.MX7 Linux development kit (RAM auto-detection) |
phycore-imx7_spl_defconfig |
imx7_phyboard_zeta_defconfig |
Default Device Tree: |
Part Number Summary
Hardware Description |
Part Number |
Configuration Details (DDR3 / DDR ECC / eMMC or NAND / QSPI NOR / Controller / EEPROM / Ethernet PHY / RTC / Temp) |
PCB Version |
|---|---|---|---|
phyCORE-i.MX7 SOM |
PCM-061-2110111C.A1 |
1GB / No / 4GB eMMC / Yes / i.MX7 Dual / Yes / Yes / Yes / Commercial |
1458.4 |
Linux Device Tree Summary
This is a summary of how the device tree source files (.dts) and the various include files (.dtsi) are broken down in the kernel. These files describe the hardware in a hierarchical and modular way to the kernel, connecting device drivers to the interfaces brought out by the carrier board.
Hardware Target |
Device Tree File Descriptions |
Filename |
|---|---|---|
phyCORE-i.MX7 kit |
Default dts Build Target (includes the other’s below) |
arch/arm/boot/dts/imx7d-phyboard-zeta-kit.dts |
Silicon-specific - adds support and enables silicon-specific features |
imx7d.dtsi |
|
SOM-specific - adds support and enables SOM-specific features |
imx7-phycore-som.dtsi |
|
CarrierBoard-specific - enables circuits supported by the SOM |
imx7d-pba-c-09.dtsi |
If designing your own custom carrier board around the phyCORE-i.MX7 SOM, you will eventually define a custom device tree for your board that includes the .dtsi file for the SOM, which PHYTEC has provided for you. All the BSP changes custom for your application should eventually be consolidated into its own Meta Layer.
Supported Interfaces
The following table outlines the validated interfaces of the default phyCORE-i.MX7 development kit.
Note
This table only outlines the key features of the phyCORE-i.MX7 PHYTEC has chosen to enable by default, which serves as a basis for customization in production designs. Unnecessary interfaces can be disabled and additional interfaces can be enabled when deploying the SOM on a custom carrier board. Other features of the phyCORE-i.MX7 may or may not be configurable depending on pin multiplexing conflicts, for more information review the phyCORE-i.MX7 schematic in tandem with the Processor Datasheet.
Interface |
Status |
|---|---|
UART |
Supported |
GPIO |
Supported |
Watch Dog |
Supported |
SD Card |
Supported |
RTC |
Supported |
I2C |
Supported |
QSPI |
Supported |
PWM |
Untested |
CAN |
Supported |
SAI |
Supported |
ADC |
Untested |
USB 2.0 |
Supported |
PCIe |
Supported |
Ethernet |
Supported |
MIPI-CSI |
Unsupported |
LVDS |
Supported |
eMMC |
Supported |
NAND |
Unsupported |
WIFI |
Unsupported |
Bluetooth |
Unsupported |
SD Card Boot |
Supported |
eMMC Boot |
Supported |
NAND Boot |
Unsupported |
QSPI Boot |
Unsupported |
USB/DFU Boot |
Unsupported |
UART Boot |
Unsupported |
Network Boot |
Unsupported |
Note
For technical support, please visit PHYTEC’s Support Portal!